AP/Client Antenna 11g 2.0

The Ferimex AP/Client Antenna 11g is wireless device integrated with an 18 dB Flat antenna. It is very easy to install, because it is connected to the computer and to the power inside the building by ethernet cable, which can be up to 50 meters long. Very little loss compared with normal cable. The PoE power supply is included. The AP/Client Antenna is designed for outdoor application and is based on TCP/IP protocols. It is easily configured over ethernet cable with a control utility in your web browser. Wireless components work in the 2.4 Ghz band, conform to the 802.11g standard, and support AP, AP Client, AP Repeater, and Bridge modes. It can also work in 802.11b mode. Reset button, LEDs, and ethernet connector accessible on the outside on the bottom of the waterproof unit. Maximum range between two units: 3 km. Maximum range to an OMNI V antenna: 2km. Beamwidth 30 degrees.

4 Modes: AP, Client, Repeater, Bridge (description below) Standard: IEEE 802.3, 802.11b and IEEE 802.11g or 802.11b Ethernet LAN: 10/100Base-T Ethernet auto sense Chipset: Realtek Frequency range: 2.400 - 2.4835 GHz Number of channels: 13 Data transfer: 802.11b: 1, 2, 5.5 ,11Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps Modulation: 802.11b: 1M: DBPSK, 2M: DQPSK, 5.5M, 11M: CCK 801.11g: OFDM Spreading: DSSS (Direct Sequence Spread Spectrum) Output power: 802.11b 17 dBm, 802.11g 13.5 dBm plus antenna gain Antenna parameters Integrated Flat 18 Antenna Reception sensitivity: min. -80 dBm at 11 Mbps, min. -68dBm at 54 Mbps Protocols: TCP/IP, IPX/SPX, NetBEUI Support: DHCP Client, HTTP Server; Roaming in the same sub-network, Default Settings Restore, Backup / Restore Setting Firmware: Basic Rate Setting, Regulation Domain Setting, DMZ, Virtual Server,IP filtering,VPN pass-through (Support PPTP, L2TP and IPsec ) Safety: 64bit/128bit WEP, ACL (MAC address filtering), WPA Waranty: 2 year Temperature range: -25°C - 50°C (operating) Humidity of surroundings: max. 95% (non-condensing) Shipping weight: 2.2 kg Power supply Power and signal are supplied through ethernet cable to the device by a Power-Over-Ethernet power supply (PoE injector), which is included free. New! Now we offer two versions of this product: Standard version - Uses Active PoE based on IEEE 802.11af standard. Offer stable power with Ethernet cables long up to 100 meters. LITE version - Uses Passive PoE which uses free wires of ethernet cable to send power to outdoor device. This is applicable with Ethernet cable long up to 20 meters. Maximum length of Ethernet cable depends on cable quality. We recommend to use Cat 5e cable. AP mode AP mode provides access for the majority of wireless stations that comply with 802.11g standards. This mode is appropriate for building points of presence for internet access. AP Client mode In AP Client mode, the device can connect to other AP/Client Antennas or other devices using Atheros, Atmel, Broadcom, or Prism chipsets in AP mode. AP Client mode is approriate for use at a client or end-user, to connect to the network. AP Repeater mode This mode allows the AP to keep the AP function role and at the same time perform communication with other 802.11g access points to establish and extend your Wireless Network coverage. Wireless Bridge mode This mode allows the connection of one or more remote LANs to a central LAN.